BONFIGLIOLI Active Cube Instruções de Operação Página 64
- Página / 176
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
62 Application manual Positioning 04/08
4.4.2.5 Single motion
A signal on Start Positioning 1222 starts the Starting Record Number 1228 (pa-
rameter
Operation Mode 1221 in setting "202- single motion, motion block from p.
1228") or the motion block set via parameters
Motion Block Change-Over 1 1224
to
Motion Block Change-Over 5 1254, (parameter Operation Mode 1221 in setting
"201-single motion, motion block via digital inputs"). After completion of the motion,
the target position is maintained.
If operation mode "Speed" or an operation mode with el. gearing is selected for
Motion Mode 1208, the drive will continue to turn until the signal on Start Position-
ing
1222 is reset or interrupted by a signal on Stop Positioning 1223.
Single motion
Input si
g
nal
s
Operation Mode
1221
=
- 201 Single Motion,
Motion Block Sel. via Digital Inputs
Operation modes for
digital outputs:
160 - Inv. Arrived at
desired Position
60 - Target Position
Reached
- 202 Single Motion,
Motion Block Sel. via P. 1228
Assign digital input signals or
logic signals to the parameters.
Selection of the motion block:
Output si
g
nals
Signal source:
282 - Tar
g
et Position
Reached
Starting-Record Number
1228
Motion Block Change-Over 1
Motion Block Change-Over 2
Motion Block Change-Over 3
Motion Block Change-Over 4
Motion Block Change-Over 5
1224
1225
1226
1227
1254
Start Positioning
Stop Positioning
1222
1223
Application manual Positioning 04/0862
- ACTIVE CUBE 1
- TABLE OF CONTENTS 4
- 1.1 General Information 7
- 1.3 Transport and Storage 8
- 1.5 Electrical Connection 9
- 1.6 Information on Use 9
- 1.7 Maintenance and Service 9
- 2 System description 10
- ACTIVE Cube 11
- 3.5.1 Getting started 20
- 3.5.2 Reference system 23
- Gear Box: Motor sha 24
- 3.5.4 Control via software 27
- Operation 30
- Operation mode 1221 33
- 4.2 Homing 36
- Function 37
- 4.2.3 Homing mode 39
- Home-Offset 40
- Home switch 40
- 4.3 Positioning Mode 41
- 4.3.2 VTable 42
- 4.4.1 Motion Mode 43
- Motion Mode 1208 44
- Motion Mode 45
- Touch-Probe-Error: Next 48
- Motion Block 1210 48
- Motion Mode 1208) 50
- Maximum Frequency 50
- Acceleration 52
- Deceleration 52
- Ramp Rise Time 53
- Delereation Ramp Fall Time 53
- Target Position/Distance 53
- Limitation 54
- 4.4.2 Motion block data 56
- 4.4.2.1 Target position 56
- 4.4.2.2 Speed 56
- Next motion block 62
- Actual Motion Block 1246 63
- Operation Mode 63
- 4.4.2.5 Single motion 64
- 4.4.3 Control of motion 65
- Assign digital input signals 66
- Deceleration 1206. If the 69
- Deceleration 1202. If the 69
- Target Position 70
- Start Positioning 71
- Stop Positioning 71
- Deceleration 1206 72
- Starting-Record Number 1228 73
- Digital Signal 1 1218 75
- Digital Signal 2 1219 75
- Digital Signal 3 1247 75
- Digital Signal 4 1248 75
- Motion Mode 1208: 76
- Speed 1203 is reached 76
- Digital Signal 3 1247 = 12 77
- 4.5 JOG Mode 78
- Jog Anticlockwise 80
- Jog-Mode Active 80
- Jog Clockwise 80
- Jog-Speed Keypad 1174 82
- Operation mode 86
- 4.7 Electronic gear 87
- 4.7.1 Master position source 87
- Master Position Source 88
- Operation Mode 1180 88
- SYNC-Time 88
- Resync. on Change of 89
- Gear Factor 1142 89
- Start Phasing 90
- Phasing: Offset 90
- Phasing: Speed 90
- Phasing: Acceleration 90
- 4.8 Monitoring Functions 92
- 4.8.1 Travel limits 92
- Operation Mode 490 of speed 93
- Pos. HW Limit Switch 1138 = 93
- Assign digital inputs 94
- Hysteresis 1149 95
- Fault Reaction 1143 96
- Fault Reaction 1144 98
- 4.8.4 Target window 101
- Fault Reaction 1120 102
- Peak Value Con 103
- Actual Appl. Warning Mask 105
- Warnings 269 105
- Speed Override 1236 106
- Hysteresis 107
- Off-Position 107
- On-Position 107
- Configuration 30 = 440 only) 108
- Operation mode 1240 109
- Feed Con 110
- Operation Mode 1240: 110
- Configuration 30 = 440 112
- 0.25-0.25 0.00 113
- Latched Position 1281 114
- 4.14 Wiring Example 115
- 440 uses internal operands 116
- 5 List of homing modes 117
- 5.1 Brief Description Homing 117
- Homing Mode 1130 118
- 5.4 Terminology 121
- Homing Mode 122
- Fast Speed 1132. When the 131
- Creep Speed 131
- Creep Speed 1133 131
- Fast Speed 1132 131
- Fast Speed 138
- Home position 139
- Pos. HW Limit Switch 139
- Actual position value 152
- Actual Motion Mode 1255 155
- Statusword 411 156
- 1125. Parameters of phasing 158
- ≤ xx ≤ 32) 162
- Constant 165
- 7 Parameter List 166
- 7.1 Actual Value Menu (VAL) 166
- 7.2 Parameter Menu (PARA) 166
- 168
- 4.2.5 1132 Fast Speed 170
Manuais e produtos relacionados com Adaptadores e conversores de corrente BONFIGLIOLI Active Cube
(27 páginas)
(74 páginas)Fujitsu LKN:Q0910P0011SE manuales
Manuales del propietario y guías del usuario para Mini pc Fujitsu LKN:Q0910P0011SE.
Ofrecemos 1 manuales en pdf Fujitsu LKN:Q0910P0011SE para descargar gratis por tipos de documentos: Ficha de datos
Comentários a estes Manuais