BONFIGLIOLI act 401 Instruções de Operação Página 66
- Página / 73
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
06/05 65
5.9 Motor temperature
Temperature monitoring forms part of the configurable error- and warnin
g
behavior.
T
he connected load can be monitored by connectin
g
a measurin
g
resistor (motor PTC)
with temperature characteristics according to DIN 44081 or by means of a bimetal
temperature sensor (break contact).
The operation mode of the motor ptc port can be selected via parameter
Operation
Mode Motor Temp.
570 The operation modes described in chapter "Motor Tempera-
ture" of the frequency inverter operating instructions are complemented by the follow-
ing operation modes with the EM-IO-02 expansion module:
Operation mode Function
11 -
EM-MPTC:
warning only
The critical operating point is displayed by the control
unit and parameter
Warnings 269.
12 -
EM-MPTC:
Error-switch-off
Error-switch-off is displayed by message F0400. Error-
switch-off can be acknowledged via the control unit or
the digital input.
13 -
EM-MPTC:
Error-switch-off,
1 min. delay
Error-switch-off according to operation mode 2, delayed
by one minute.
14 -
EM-MPTC:
Error-switch-off,
5 min. delay
Error-switch-off according to operation mode 2, delayed
by five minutes.
15 -
EM-MPTC:
Error-switch-off,
10 min. delay
Error-switch-off according to operation mode 2, delayed
by ten minutes.
The function to be adjusted by parameter
Operation Mode Motor Temp. 570 results in
si
g
nalin
g
the overtemperature by the red LED of the frequency inverter, irrespective o
f
the selected operation modes of the control inputs and outputs.
The operation modes with error-switch-off result in the fault messa
g
e "FAULT" with
fault number "F0400" being displayed on the control unit KP500.
The fault message can be acknowledged via parameter
Program 34 or the lo
g
ic si
g
nal
linked with parameter
Error Acknowledgement 103.
Thermal switch
S3IND
S4IND
S5IND
0
Therm. Contact
204
Operation Mode Motor Temp.
570
Error/Warning-Behaviour
PTC connection
S1IND
S2IND
S6IND
MFI1D
EM-PTC
EM-PTC
The function selected according to the above table with parameter Operation Mode
Motor Temp.
570 can be linked, as required, to the di
g
ital control outputs and the
warning mask. (For detailed information, refer to the operating instructions of the fre-
quency inverter).
- Expansion module EM-IO-02 1
- 1.1 General information 6
- 1.2 Proper use 6
- 1.3 Transport and storage 7
- 1.5 Electrical connection 7
- 1.6 Operation information 7
- 1.7 Maintenance and service 7
- 2 Introduction 8
- 3.1 General 9
- 3.2 Mechanical installation 9
- 3.3 Electrical installation 11
- 3.3.1 Circuit diagram 11
- 3.3.2 Control terminals 12
- 4 System bus interface 13
- 4.1 Bus termination 13
- 4.2 Cables 14
- 4.3 Socket X410B 14
- 4.5 Setting node address 15
- 4.6 Functional overview 16
- 4.7 Network management 16
- 4.8 Master functionality 18
- Identifier 20
- SYNC-Time 919 20
- Inverter 1 22
- Inverter 2 Inverter 2 22
- System bus 22
- 4.9 Slave functionality 23
- 4.9.1.1 Boot-up message 23
- 4.9.1.2 Status control 23
- 4.9.2 Process SYNC telegram 24
- 4.9.4 Server SDO1/SDO2 26
- SDO2 Set Active 923 27
- 4.10.2.1 Profibus-DP 30
- 4.11.5 Virtual links 36
- 4.12 Control parameters 43
- 44 06/05 45
- 4.14 Utilities 46
- Load system bus 50
- Total load [%] 70 50
- 5.1 Analog input EM-S1INA 51
- 5.1.1 General 51
- Y +−⋅= 52
- 5.1.4.1 Examples 53
- Tolerance band 560 is not 54
- 5.1.5 Scaling 55
- 5.1.8 Adjustment 58
- 5.1.9 Filter time constant 58
- 5.2.1 General 59
- 5.2.2 Operation modes 59
- 5.2.3 Adjustment 59
- 5.2.4.1 Examples 60
- 5.3.1 General 61
- 5.3.2 Operation modes 61
- 5.4 Digital inputs EM-SxIND 61
- 5.5.1 Division marks 62
- 5.5.2 Actual speed source 63
- 5.7 Actual value display 64
- 5.9 Motor temperature 66
- Operation Mode 465 67
- 6 Parameter list 68
- 6.1 Actual value menu (VAL) 68
- 6.2 Parameter menu (PARA) 68
- % -100.00 ... 100.00 5.2.4 69
- 7 Annex 71
- 7.1 Error messages 71
- INDUSTRY PROCESS 73
- AND AUTOMATION SOLUTIONS 73
- COD. VEC 218 R0 73
Manuais e produtos relacionados com Adaptadores e conversores de corrente BONFIGLIOLI act 401
(176 páginas)
(74 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais